Free Essay

Unit 5 Cabling Factors

In: Computers and Technology

Submitted By dsgrippi
Words 256
Pages 2
4/14/2014
Unit 5. Assignment 1: Cabling Factors and Tools Discussion

Three factors that need to be considered is being fire protected, water proof, and shock protection. Being fire protected, just in case a fire occurs, the wiring would be protected by a casing around the actual wires which in cause wouldn’t melt the casing and destroy the wires. Since the data room is usually in the basement of companies, if a flood occurs, there are wires that are protected by a casing that would not let water intrude into the casing. For shock protection, there is always a chance for a shortage to happen. Wiring and a lot of electricity used. For example, if there is a storm going on and lightning hits a generator and shorts everything out, it would not fry the wiring if they are protected from the shock. The two most important considerations to take into account when either pre-wiring a house or wiring after the house is complete, are the routing of the cable and the quality of the wire used. These two points are often overlooked and the decision to wire the house at all often comes as an afterthought, when most if not all of the interior of the structure has been completed. Some tools that would be useful to use are cable cutters, hole cutting tools, wire strippers, punch down tools, RJ45 connector crimp kits, pliers and cutters, label makers and electrical tape. The makeshift tool that we would use is a staple gun.…...

Similar Documents

Premium Essay

Unit 5

...could benefit from “smart” technologies? Describe one example not listed in the case. One good thing we can learn from installing smart grids into households is knowing that consumers will be willing to spend the amount of money for these smart technologies will make them become successful and business, which helps companies manage the smart grids. Just how a “smart” phone is like a computer inside a cellphone is the same way a smart grid will be with the electricity grid. There will be more two-way communication digitally and it allows consumers to adjust the electricity from a small device. Another big benefit is knowing the system is modernized and you don’t have to wait for utility workers to come out and fix your electricity. 5. Would you like your home and your community to be part of a smart grid? Why or why not? Explain. Yes. I wouldn’t mind me, or my community being part of a smart grid. It would definitely be good to know how much energy I use every month and help me make better decisions. The only challenge would be paying the expensive costs to get the smart grids installed, but a big investment like that would be worth it. If my smartphone can make things on my cellphone a lot easier, I don’t see why it wouldn’t do the same for my electric system in my house. Chapter 2, pg 77 1. What is Procter & Gamble’s business strategy? What is the relationship of collaboration and innovation to that business strategy? P&G’s business strategy has......

Words: 2332 - Pages: 10

Premium Essay

Unit 5

...UNIT 5 INDIVIDUAL PROJECT BUSN105 – Introduction to Business by La’Ketica T. Moore AIU Online April 22, 2013 Abstract In this unit I was asked to describe an organization basic legal, social, and economic environment. I am asked to describe the management structure and its operational and financial issues. Research and identify the impact of potential change factors including the role of technology. UNIT 5 IP Introduction The organization that will be discussed in this paper is healthcare this organization is important to this writer because it is her chosen field of employment. It is important to learn about healthcare because of all the recent changes to the law on a state, local, and federal level. This writer feels in order to learn about the healthcare regulations you need to learn about your rights as either a provider or as a patient. Basic Legal Environment The healthcare industry has come up on several changes over the past years that lead to lawsuits. Some of the legal issues that the healthcare has to deal with would be HIPPA which is the Health Insurance Portability and Accountability Act which protects the privacy of individually identifiable health information. OSHA assures the safe and healthful working of men and women by setting and enforcing standards and providing training, outreach, education and assistance. Patient documentation and communication which sparked the malpractice lawsuits over a decade ago, in keeping the patient......

Words: 841 - Pages: 4

Free Essay

Unit 5 Assignment 1 Cabling Factors and Tolls Discussion

...Unit 5 Assignment 1 Cabling Factors and Tolls Discussion Flexibility What type of install is the cable going into? Is everything in a fixed position? If you have an install where items are moved around without being disconnected, using highly flexible cable is necessary. Cables in these scenarios need to be flexible to meet those demands of mobility, and also for the life of the wire so that it does not crack, break, fray or short. We had a job at a university where we moved flat panels on a track system to create different screen sizes, and for that we had to make sure the cable would meet the demand. Capacitance Cat 6 is not always better than Cat 5. If a video extender is made for Cat 5e, using Cat 6 may cause you a problem. The electrical properties are different, and the circuitry inside may not be able to reconcile the increased capacitance. You should confirm with the manufacturer before making a substitute in a Category cable. Jacket What type of jacket does your cable need? You have plenum, riser, PVC/non-plenum and direct burial. Plenum cable is often required in commercial work, especially in buildings where there are open-air returns; it is essential to meeting code. Integrators will often use riser grade at the riser, and then transfer to plenum in the plenum space. This saves some cost, but I recommend you second-guess saving that few cents per foot in most cases. The chances of mixing up a box of cable and pulling riser in the plenum space may......

Words: 318 - Pages: 2

Free Essay

Cabling Factors and Tools Discussion

...Cabling Factors and Tools Discussion When performing cable installations there are three factors that need to be considered, fire protection, water intrusion or flood protection, or changes in the structural foundation in your home. The two most important considerations to take into account when either pre-wiring a house or wiring after the house is complete, are the routing of the cable and the quality of the wire used. These two points are often overlooked and the decision to wire the house at all often comes as an afterthought, when most if not all of the interior of the structure has been completed. Pre-wiring your house, or installing the wire in the stage of construction just before the drywall goes on, is always the preferred method and offers the most flexibility in placement of outlets and the routing of your cable .When deciding on the location of your outlets, try to visualize where you'll eventually be placing the furniture in the room in relation to the location of your television. Internet services are also being provided now by a lot of cable companies so placing an outlet in a spot near your planned computer station is also a good idea .In general it's a good idea to put at least one outlet in every room whether or not you plan to use it immediately. At least it will be there when it is needed, avoiding the drilling of any unsightly holes in the future. Outlet boxes can be purchased at any hardware store and should be fastened to the wall stud in the......

Words: 988 - Pages: 4

Premium Essay

Cabling Definitions Unit 4

...Definitions Horizontal Cable – cable between telecommunications outlet and the horizontal cross-connect Backbone Cable – cable between telecommunications and equipment room Patch Cord – cable between network device and main cable run or outlet Connectors – device attached to end of “cabling” that attaches to another Conduit – section in which cables are housed for protection Racks – frame where panels, switches, and other equipment are installed Punch-Down Blocks – cross connect block where the wires are placed into a terminal groove and “punched down” with a special tool Consolidation Points – location for interconnection between building and work area pathways Crimpers – device used to install a crimp on connector Fish Tape – tool used to route wiring through walls or conduit Cable Toner – electronic device used to test cables for breaks and other problems Continuity Tester – device used to test cables for uninterrupted pathway for signal Category 5e/6 Cable – twisted pair cable with 100 ohm impedance and 100mhz freq. Binder Groups – group of 25 or more twisted pair wires Hybrid/Composite Cable – cable that has at least 2 types of media inside Pulling Cable – used to pull cable through conduit or over racks (similar to fish tape) Wavelengths of Light – distance an electromagnetic wave travels in the time it takes to oscillate through a complete cycle EMI – noise generated in copper conductors Optical-Fiber Strand – assembly consisting of one or more......

Words: 304 - Pages: 2

Premium Essay

Unit 5

...Kelly McLoughlin PT1420 Week 1 Assignment 1 Review Questions 1. A( n) __________ is a set of instructions that a computer follows to perform a task. (B) Program 2. The physical devices that a computer is made of are referred to as __________. (A) Hardware 3. The part of a computer that runs programs is called __________. (D) Cpu 4. Today, CPUs are small chips known as __________. (B) Microprocessor 5. The computer stores a program while the program is running, as well as the data that the program is working with, in __________. (C) Main Memory 6. This is a volatile type of memory that is used only for temporary storage while a program is running. (A) RAM 7. A type of memory that can hold data for long periods of time— even when there is no power to the computer–– is called __________. ( C ) Secondary Storage 8. A component that collects data from people or other devices and sends it to the computer is called __________. (B) An Input Device 9. A video display is a( n) __________. (A) Output device 10. A __________ is enough memory to store a letter of the alphabet or a small number. (A) Byte 11. A byte is made up of eight __________. (D) Bits 12. In a( n) __________ numbering system, all numeric values are written as sequences of 0s and 1s. (B) Binary 13. A bit that is turned off represents the following value: __________. ( C ) 0 14. A set of 128 numeric codes that represent the English letters, various punctuation marks, and......

Words: 454 - Pages: 2

Premium Essay

Unit 5

...Unit 3 Coaxial cable is a cable that has an inner conductor surrounded by a tubular insulating layer, surrounded by a tubular conducting shield. Coaxial cables were designed to solve a problem with the transmission of high-frequency radio signalsCoaxial cable does not need optical conversion technology. | signal quality can be a problem in environments with very high levels of electrical noiseFaulty cable shielding can allow cross talk with data jumping from line to line. Because the cable is electrically conductive it makes equipment vulnerable to lightning damage. | Fiber optic cable transfer data via light waves. They are made from glass or plastic fibers in the core of the cable surrounded by a cladding layer and a buffer coating which protects the fibers from moisture and other damage Fiber optic data transmission is incredibly fast.Fiber optic cables can transmit data over exceptionally long distances without much data loss. | Fiber optic cabling can cost more than double what a typical broadband connection costs.Fiber optic connections are not available in many areas | Shielded twisted pair cables is an electrical cable of one or more insulated conductors enclosed by a common conductive layer Shielded twisted pair wires are less susceptible to electrical interference caused by nearby equipment or wires | it is physically larger and more expensive than twisted pair wireit is more difficult to connect to a terminating block | unshielded twisted......

Words: 304 - Pages: 2

Free Essay

Unit 5

...network. A proper cabling system design is extremely important to a well-functioning cabling infrastructure. Along with any other major project the key to a successful cable installation is planning. A proper cabling system design is nothing more than a plan for installing the cables and to which devices they will be associated with. Another aspect of a successful cabling installation is the use of quality goods. The quality of the goods used when performing a install will directly affect the transmission efficiency of the network. The old saying “You get what you pay for” really applies to this situation, so don’t be afraid to spend a little more money for quality products. Workmanship is the key to success when talking about properly installing cabling. Poor workmanship during an install can cause data-transmission problems and can lower the networks effective throughput. Rushing a cabling installation for the sake of a deadline will most of the time result in having to re-do it because of excessive twisting and untwisting of cables. Aside from workmanship, proper cabling, and quality goods there are three factors to take into consideration when performing a cabling installation. Those three areas for consideration are: Physical protection, Electrical protection, and Fire protection. These three categories of importance all fall under Cabling Management. Physical protection is important because some cables can be very fragile. When performing a cabling......

Words: 615 - Pages: 3

Free Essay

Cabling Factor

...installation there is certain factors which need to be addressed prior to starting your design. Planning is one of the most important aspects or a proper design for your installation. Deciding where your cables are going to be ran what equipment you’re going to need to set up the network system. What tools you’re going to need to achieve the desired outcome and materials. Also, making sure the area you are going to be installing in is up to NFPA, FCC, UL, NEC code. Verifying that a system is safe from harming any occupants that may inhabit the structure is key to quality and control. Also if your equipment is safe and of good quality not only will your system be safe but also run better. If you have wires hanging out, shorts in networking hardware, systems that run too hot and placed in tight areas with no ventilation just some examples. Some aspects of proper design are having a detailed plan of how the installation will proceed, you should know the scope of the project, and i.e.…how many cable runs you have what connections need to be made. Your design should also be made available to all people involved with the installation. As well as contain a blueprint of how the cables will be installed. Tools that will be useful in your installation will be, Wire cutters, crimpers, pen and paper, fish tape, pull string, two way radio, labeling materials, punch down tool, toning tools, basic hand tools. I know I have used off the book tools to install cabling. One of the tools......

Words: 355 - Pages: 2

Free Essay

Unit 5

...P5- explain the strategies and methods that can be used to support children, young people and their families where abuse is suspected or confirmed. There are many factors that could lead the individual to suspect a child to be abused. These factors could be s howed through the individuals apprentice or the way in which they act. Health professionals use a variety of strategies and responses to help and support children and young people. For example if an individual’s self-esteem, confidence and resilience is low there become more vurable and at target for abuse. Whereas if a child or a young person has high self-esteem they will confident and less likely to be a target of abuse they are more likely to be talkative and notice that they are becoming a target of abuse. A child or young person with low self-esteem will be vulnerable as they are less likely speak out. To address this health and social care professionals should make the individuals feel valued and the child or young person should be aware and reminded of the qualities they have. This strategy would be appropriate in some situations but not others for example if an individual is beginning to act out at school this could be a clear sign there self esteem is quite low as they are putting a front on rather than showing weakness, by addressing this low self esteem individuals will begin to feel better about them self and express there feelings. The more we work on an individual self esteem the less likely......

Words: 2104 - Pages: 9

Premium Essay

Unit 5

...maps can be drawn by hand, either as "rough notes" during a lecture or meeting, for example, or as higher quality pictures when more time is available. Diagrams that visually map information using branching and radial maps trace back centuries. These pictorial methods record knowledge and model systems, and a long history in learning, brainstorming, memory, visual thinking, and problem solving by educators, engineers, psychologists, and others. Some of the earliest examples of such graphical records were developed by Porphyry of Tyros, a noted thinker of the 3rd century, as he graphically visualized the concept categories of Aristotle. Philosopher Ramon Llull (1235–1315) also used such techniques (Willis). A mind map contains that following 5 elements. The main idea, subject or focus is crystallized in a central image. The main themes radiate from the central image as 'branches'. The branches comprise a key image or key word drawn or printed on its associated line. Topics of lesser importance are represented as 'twigs' of the relevant branch. The branches form a connected nodal structure.(Buzan) BIBLIOGRAPHY 'Mind maps as active learning tools', by Willis, CL. Journal of computing sciences in colleges. ISSN: 1937-4771. 2006. Volume: 21 Issue: 4 Mindmapping.com, Note-taking That Litera...

Words: 333 - Pages: 2

Premium Essay

Unit 5

... Establish a sense of urgency. Leaders within an organization should work to inspire members to sense that change is necessary. Leaders should call upon members of the organization to cooperate and appeal to their shared values at this stage. * 2. Form a powerful guiding coalition. At this stage, leaders create a unified team of people who can lead the change effort. Leaders should choose members who have credibility and expertise in the eyes of employees. * 3. Create a vision and strategies for putting that vision into practice. A statement of vision for change should be easy for employees to understand. * 4. Communicate the vision. Leaders should communicate and reinforce the vision through daily activities and actions. * 5. Empower others to act on the vision. Employees must be encouraged to take risks and engage in nontraditional activities and ideas. * 6. Plan for and create short-term successes. The guiding coalition can help plan for and create short-term successes by setting concrete, achievable goals and mapping out clear ways to achieve them. * 7. Don't let up. Kotter cautions leaders not to let up when results begin to show, but rather to add more projects, empower more employees to help with change, and expand change efforts. * 8. Institutionalize new approaches. New practices should be made a part of the organization's culture. Leaders may accomplish this by communicating the connection between the new behaviors and organizational......

Words: 351 - Pages: 2

Premium Essay

Unit 5

...PUBLIC SERVICES LEVEL 3 – 2016 UNIT 5 Part 1 – PHYSICAL PREPARATION NAME: Rohan Monsy (11024319) Unit 5 - Assessment and grading criteria | To achieve a pass grade the evidence must show that the learner is able to: | To achieve a merit grade the evidence must show that, in addition to the pass criteria, the learner is able to: | To achieve a distinction grade the evidence must show that, in addition to the pass and merit criteria, the learner is able to: | P1 describe a fitness assessment for each of the major components of fitness | M1 explain the results of the fitness assessment and measure against relevant public service entrance test | D1 evaluate results of the fitness assessment, analyse strengths and recommend improvements | P2 describe the structure and function of the muscular-skeletal,cardiovascular and respiratory systems | | | P3 undertake a fitness activity,record and identify the short-term effects of exerciseon the major human bodysystems | M2explain the short and long term effects of exerciseon the major human bodysystems | | P4 describe the lifestyle factors that can affect health | M3explain the effects ofidentified lifestyle factors onhealth and fitness, whenapplying for public service and long-term employment | D2Evaluate the effects ofidentified lifestyle factors onhealth and fitness, whenapplying for public service and long-term employment | P5 Provide lifestyle improvement strategies that can have a positive effect on health | M4Explain......

Words: 2802 - Pages: 12

Premium Essay

Unit 5

...individuals and the nation, using selected examples. | |Discuss how different types of health promotion are used to benefit the health and wellbeing of individuals and the nation, using selected | | |examples. | | M1/D1 Unit 5 |Name & type of Health promotion |Describe what it shows [Effect of alcohol & impact of alcohol] |What message is it trying to promote? |How could this benefit the individual? |How could this benefit the nation? |Is this an effective promotion? | |[E.g. leaflet/poster/video] | | | | |Explain your answer giving some examples of statistics | |Reference | ......

Words: 1717 - Pages: 7

Premium Essay

Unit 5

...IT113 Unit 5 Homework Chapter 6 1. What are the 3 basic tools required to install a plug for UTP cable? A. Stripper (the wire kind), wire cutter, cable crimper 2. What type of fiber-optic tester should you purchase to make sure the fiber-optic cable was installed without any fault and that enough light is being transmitted through the fiber, and what are the three key attributes to know before you purchase a tester? A. You want the tester to have the capability for correct fiber connectors, support the correct type of fiber (single vs. multi mode) and test appropriate wavelength. You should purchase an attenuation tester since you are testing for the power of the light transmission. 3. Which of the following supplies enables the reduction of friction on the cables while being pulled? A. Wire pulling lubricant Chapter 9 1. What are the main aspects that must be addressed when designing and installing wall plates? A. Fixed or modular design wall plate, wall plate location, manufacturer system, and wall plate mounting system. 2. Which TIA standards should you refer to for ensuring proper design and installation of wall plates? A. Residential is ANSI/TIA-570-B, Commercial is ANSI/TIA-568-C.1 3. Your commercial office building environment is expected to change over the next few years as some of the network devices that are presently installed with coax connections need to be converted to RJ-45 and some network devices that are currently RJ-45 connections may......

Words: 408 - Pages: 2